Specifications:

• This is a high quality Replacement LCD Screen for iPod nano 5th Gen
• It's for Apple iPod nano 5th Generation model only
• Easy to fit, high resolution, high quality material, high meticulously crafted & provide clear and stable view
• High quality material, high meticulously crafted, provide clear and stable view
• The LCD Screen is used to repair faulty screen: display problems, dead pixels, cracked LCD screens, wrong color issues 
• This is a non-OEM product
• Compatible with: iPod nano 5th Gen

Details:

• This is a high quality Replacement LCD Screen for iPod nano 5th Gen

 

• The LCD Display Screen is easy to fit, high resolution, high quality material, high meticulously crafted & provide clear and stable view

How to Repair a Cracked iPod Screen:

• Place a bath towel on a table. Place the iPod nano face up on the towel with the dock connector at the bottom closest to you.
• Insert the tip of the iPod opening tool into the seam between the bottom plate and the nano's case on one side. Slide the tip across the width of the nano to loosen the plate from the case. Repeat this on the other side of the plate. Insert the tip into the center of the plate and lift upwards. Pull the plate off the bottom and place it aside.
• Remove the screws now revealed on the bottom with the #8 Torx screwdriver. Insert the tip of the iPod opening tool into the seam between the bottom plate and the headphone jack inside the left side of the nano. Lift up on the tip to loosen the headphone jack. Pull the headphone jack out of the bottom of the nano, but do not break off the attached connecting cable.
• Remove the screw revealed from under the headphone jack with the Phillips jeweler's screwdriver. Slide the switch at the nano's upper right corner so the orange stripe is seen.
• Insert the tip of the iPod opening tool into the seam between the top plate and the nano's case on one side. Slide the tip across the width of the nano to loosen the plate from the case. Repeat this on the other side of the plate. Insert the tip into the center of the plate and lift upwards. Pull the plate off the top and place it aside. Remove the screws now revealed in the top with the screwdriver.
• Insert the tip of the iPod opening tool into the bottom of the nano. Push up to raise the logic board out of the top. Grip the edge of the circuit board at the top and pull it out of the nano. Place the logic board on the towel face up.
• Insert the edge of the razor blade into the seam on one side between the LCD panel and the logic board. Slide the razor blade across the length of the LCD panel to loosen its hold on the logic board. Repeat this on the right side of the LCD module and along the top. Pull the LCD module off the case. Insert the tip of the iPod opening tool into the ribbon connector on the logic board going from the LCD module. Lift up on the tip to loosen the plug. Pull the plug out of the logic board.
• Place the LCD module on the towel face up. Insert the tip of the flat-edged screwdriver into a clip on one side of the LCD module. Lift up on the tip to release the clip. Repeat this on the other side of the LCD module.
• Pull the glass out of the LCD module's frame. Dispose of the glass properly. Place the replacement glass into the frame. Push down on both sides of the LCD module to reengage the clips.
• Reattach the ribbon connector to the logic board. Apply glue from a glue stick to the back edges of the LCD module. Place the LCD module on the logic board in the position it formerly occupied. Press down lightly on the sides of the LCD module. Let the glue set for 10 minutes before proceeding.
• Insert the bottom of the logic board into the top of the nano's case. Push the logic board back into the nano. Reattach the screws on the top of the nano. Place the top plate back into position. Reattach the screws.
• Reattach the screw to the bottom of the nano. Push the headphone jack back into the bottom of the nano. Reattach the screws. Place the bottom plate back on the nano. Reattach the screws. Slide the switch at the upper right corner of the nano so the orange stripe is no longer visible.

Package Included:

• 1 x Replacement LCD Display Screen for iPod nano 5th Gen