WOW!!!
PEAVEY SUPREME TRANSTUBE
100 WATT HEAD
Auction is for a very good condition Peavey Supreme Transtube series 100 Watt guitar amplifier. Overall in great shape.. not abused.. well cared for.. check out the pics for a good idea of the condition. Comes with footswitch.
Here are some specs and features from the owners manual which you can download fom the Peavey website: Supreme TM TransTube@ Series.
This amp represents years of research on vacuum tube emulation, resulting in a totally new Supreme. The preamp has been redesigned, using patent-applied for technology that redefines tubelike distortion and harmonic generation in solid-state amps. The new T. Dynamics circuitry, also awaiting several patents, creates the long sought for tube power compression phenomenon. This, in combination with resonance and presence circuitry, yields the closest tube amp simulation to date. This compression effect is increased by turning the T. Dynamics control down, which lowers the power level the amp puts out. To further enhance the performance of the Supreme, an impedance-matching transformer is used to deliver 100 watts into 16, 8, or 4 ohms; and a footswitchable effects loop allows for even greater flexibility.
FRONT PANEL FEATURES POWER SWITCH (1) Depress the switch to the on position. The red LED will illuminate indicating power is being supplied to the unit.
POWER LED (2) Illuminates when AC power is being supplied to the amp.
T. DYNAMICS CONTROL (3) Adjusts the power level of the amplifier from 10% to 100% power. When set to lower settings, the power compression simulation will be much more pronounced.
PRESENCE (4) An active tone control that boosts the extreme high frequencies by 6 dB.
RESONANCE SWITCH (5) Used to fine-tune the low frequency range of the speaker enclosure by varying the damping factor of the amplifier between two presets.
EFFECTS LEVEL SWITCH (6) Selects the effects loop operating level: -10 dBV (0.3 V RMS) when out and 0 dBV (1 V RMS) when in.
EFFECTS RETURN (7) Input for returning signals from external low-level effects or signal processing equipment.
EFFECTS SEND (8) Output for supplying signals to external low-level effects or signal processing equipment.
REVERB LEVEL (9) Controls the overall reverb level. POST GAIN (10) Controls the overall volume level of the Lead channel. The final level adjustment should be made after the desired sound has been achieved.
LOW, MID, & HIGH EQ (11,15) Passive tone controls that regulate the low, mid, and high frequencies for the Lead and Clean channels, respectively.
GAIN SWITCH (12) Boosts the overall system gain. Depress to the in position to activate.
THRASH SWITCH (13) Notches the mid range about 20 dB. PRE GAIN (14) Controls the input volume level of the Lead channel.
CHANNEL SELECT SWITCH (16) Allows selection of the Lead or Clean channel. The in position of the switch selects the Lead channel and the out position selects Clean. NOTE: Channel selection may also be achieved by the remote footswitch. If remote selection is desired, the channel switch must be in the in (Lead) position.
BRIGHT SWITCH (17) Provides a preset boost (6 dB) to treble frequencies. To activate, depress the switch to its in position.
VOLUME (18) Controls the volume level of the Clean channel.
LOW GAIN INPUT (19) Provided for instruments that have extremely high outputs, which can result in overdriving (distorting) the High Gain input. If both inputs are used simultaneously, the output levels are the same (both are low gain).
HIGH GAIN INPUT (20) Used for most electric guitars. It is 6 dB louder than the Low Gain input. Rated Power & Load: Power specs measured with T. Dynamics @ 10% 100 W RMS into 16, 8, or 4 ohms Power @ Clipping: (typically) (5% THD, 1 kHz, 120 V AC line) 100 W RMS into 16, 8, or 4 ohms Frequency Response: +O, 3 dB, 60 Hz to 20 kHz, @80WRMS Hum & Noise: Greater than 86 dB below rated power Power Consumption: Domestic: 300 W @ 60 Hz, 120 VAC Export: 300 W @ 50/60 Hz, 220-230/240 V AC
PREAMP SECTION The following specs are measured @ I kHz with the controls preset as follows: Push Bright, Off (out) Channel Select Normal (out) Low& High @ 10 Mid 63 0 Presence @ 0 dB Pre & Post Gain @ 10 Gain & Thrash, Off (out) Normal Levels are with normal volume 625 Minimum Levels are with normal volume @ IO
SPECIFICATIONS Preamp High Gain Input: Impedance: High-Z, 1 M ohm Nominal Input Level: -14 dBV, 200 mV RMS Minimum Input Level: -24 dBV, 60 mV RMS Maximum Input Level: 0 dBV, 1 VRMS Preamp Low Gain Input: Impedance: High-Z, 44 K ohms Nominal Input Level: -8 dBV, 400 mV RMS Minimum Input Level: -18 dBV, 120 mV RMS Maximum Input Level: 6 dBV, 2VRMS Effects Send: Load Impedance: 1 K ohm or greater Nominal Output Level: -10 dBV, 0.3 V RMS or 0 dBV, 1 V RMS if Effects Level is in Effects Return: Impedance: High-Z, 22 K ohms Designed Input Level: -10 dBV, 0.3 V RMS or 0 dBV, 1 V RMS if Effects Level is in (Switching jack provides Effects Send to Effects Return connection when not used) Preamp Output: Load Impedance: 1 K ohm or greater Nominal Output Level: 0 dBV, 1 VRMS Power Amp Input: Impedance: High-Z, 30 K ohms Designed Input Level: 0 dBV, 1 VRMS (Switching jack provides preamp output to power amp input connection when not used) System Hum & Noise @ Nominal Input Level: (20 Hz to 20 kHz un weigh ted) 72 dB below rated power Equalization: Special low, mid, & high passive type EQ Presence: +6 dB @ 5 kHz Push Bright: +6 dB @ 2 kHz Push Thrash: -20 dB notch @ 1 kHz in Lead channel Push Gain: Increases Lead gain Push Resonance: +6 dB @ cabinet resonance External Footswitch Functions: Lead Channel Defeat (when selected with button) Effects Loop Bypass
Dimensions & Weight: 10.25 H x 24.375 W x 11.25 D 35.7 Ibs.
Shopping Cart