Inspired Studios Wall Art can wrap around wall corners or poles and be placed on ceilings.  The material is re-positional and may be re-used over and over again.  Read the instructions below to be sure you install correctly to increase the life of your Wall Art :)

Inspired Studios Wall Art is great for your home, office, and even your vehicle!

Installation Instructions

CHOOSE YOUR SPOT TO SHOW YOUR ART!

Pick a smooth, dry and clean surface –The most traditional places are on any wall, door (cabinet door), window or car (do not block windshield).  When placing your wall decal on a standard painted wall, make sure the wall had been previously primed prior to painting (otherwise the paint may possibly come off) and has had at least 30 days to dry (gas out).  If you place your wall decal on a pebbly, textured or porous surface (i.e. brick or cement walls), you may receive poor results (mainly if not painted) but in most cases it has worked (longevity varies on outdoor conditions).  Please test any questionable surfaces before making a large investment.

CLEAN BEFORE YOU STICK IT

Use a warm damp cloth or sponge to clean most surfaces, wipe down and let dry.  Outdoors you may need to power wash. We have had success with all paints, gloss, matte, latex… but the hardest surface to stick to is a textured surface using a eggshell paint (tackiness may vary as eggshell paint has anti graffiti proof chemicals in them (primarily used in the kitchen) not allowing anything (temporary) to stick to it . You can remove and replace the wall decal over and over again, however, once the adhesive collects too much dust, dirt, or fibers it will become less effective, and the wall decal may not stick as well to your surface.  

PEEL AND STICK IT

Depending on the size of your wall decal it may be helpful to have two people install it.  Try not to let the adhesive come together, or the wall decal to fold up against itself.   It’s okay if it does, you can separate it by carefully pulling it apart so you do not ruin the print. 

Start at the top of your wall decal (for “Photo Tree” decal, start at the bottom/trunk) and pull down approximately 2-3” of the backer. By lightly pressing and smoothing, apply the 2-3” exposed adhesive area of your wall decal to your chosen surface area.  Then continue to slowly pull the backer downward in 2-3” increments smoothing the wall decal as you go.  Once the wall decal is started, it may be helpful if another person holds the bottom and pulls down slightly giving some tension and keeping it straight and easier to apply. 

If there are any bubbles or wrinkles, you can lightly press or smooth them out, or just peel back that area and re-apply.  Please Note:  Pressing too hard will not damage the, wall decal however, it may cause your hands to gather ink (due to the natural oils on your hands), and it could transfer from your hands onto another surface.   

SUGGESTIONS

If a bubble re-appears over the next day or two, you can remove it by pressing and lightly rubbing it.  This may happen occasionally because oil, dirt or dust could be on your surface.  You can use a pin to pop the bubble and then smooth it out with your fingers in a circular motion.  If it keeps re-appearing, you may want to move your wall decal to another area. 

OUTDOORS

With our patented adhesive you can place your wall decal on any outdoor flat surface; however, it may fade after 6-12 months of strong sun exposure. It has lasted up to 2 years before fading. The material will stay in place on a car for a long time, but car washes will eventually wear it out.   The blank adhesive material manufacturer has thoroughly tested it on the outside of cars, racecars, boats and airplanes over a two-year period.  To ensure your wall decal stays on a moving surface, it is very important when applying it that there are no air gaps.   Simply use the back of a spoon on top of the wall decal to smooth it tightly into cracks and around bends. Do not place Wall decal on CAR windows. 

Questions: contact [email protected] 

*Be sure to KEEP your “backer paper” for storage of the wall decal between uses.  ALWAYS put your wall decal back on the “backer paper” when your decal is not on display.

Do NOT stick wall decals to any other kind of paper!